How Make a Popsocket Stick Again

Download Commodity

Download Article

PopSockets are very useful for getting a better grip on your telephone, but they can get muddied with time and the adhesive that sticks it to the back of your telephone can get loose and lose its stickiness. Afterwards removing it from your phone, merely soak information technology in water and scrub it with soapy water your PopSocket to make information technology await good as new and stick equally if y'all bought information technology yesterday.

1. 1

   Fill up a shallow dish with cold tap water. Grab a shallow dish, such as a small bowl or a deep plate, and fill it with about .5 in (ane.iii cm) of very cold tap water. This is to ensure that you only soak the adhesive side of the PopSocket — you should make clean the plastic grip separately.

   • Even if your PopSocket is larger than normal, using only a .v in (i.3 cm) layer of water will ensure that but the adhesive side touches the h2o when information technology is extended.

2. 2

   Remove the PopSocket and place it gluey-side down in the h2o. Dig your fingernail under the PopSocket to pry information technology off of your telephone, then pull the plastic grip to it extend to its full length. Place the agglutinative side down in the h2o and so the plastic grip pokes in a higher place the surface of the water.

   • Exist sure that your extended PopSocket rises above the surface and bleed out water equally necessary to avoid getting the rest of it moisture.^[1]

   Advertisement

3. 3

   Permit the PopSocket soak for almost ten seconds, then remove it. Don't disturb the water and don't take it out before 10 seconds are up. Once x seconds have passed, quickly take it out of the water by the grip and shake off whatsoever excess h2o. Exercise not let information technology soak for more than ten seconds or it could ruin the adhesive. ^[2]

   • If y'all are concerned about ruining the adhesive, run the PopSocket nether cold water for a few seconds instead, although soaking information technology is more effective.^[three]

4. four

   Lay a newspaper towel downward and place the PopSocket sticky-side up. You can use a regular kitchen towel or a linen towel, depending on what you take readily available. Lay the PopSocket with the pasty side pointing upwardly and the blueprint and plastic grip touch the newspaper.^[four]

5. 5

   Allow the agglutinative side of the PopSocket dry for 10 minutes. Leave your PopSocket to dry for ten minutes at virtually, and keep an eye on it as it dries to see if it finishes sooner.^[5] Avoid using a hair dryer or dabbing it with a towel or you could harm the adhesive and brand it less sticky. Just let information technology air dry out, and swiftly re-attach information technology to your telephone the moment it is dry by pressing the sticky side firmly onto the dorsum of your phone.

   • Do non let your PopSocket dry out for more than 15 minutes at most or it may lose its ability to stick.
   • If y'all accidentally go out it out, run it under common cold water for a few seconds then let information technology dry over again, although be aware that it may non regain its stickiness.

   Advertizing

1. one

   Remove whatsoever additional stickers you lot've added to the finish of the PopSocket. If you added stickers to the PopSocket'due south grip, you volition need to remove them before yous clean it. If the adhesive is nonetheless practiced on the sticker feel gratuitous to put information technology back on after cleaning, otherwise y'all will take to simply throw information technology abroad and find a new one.

   • PopSockets ordinarily come with some kind of pattern on the finish of the grip, so even if you have to remove whatever additional stickers you've added, it will still have an aesthetic pattern.^[6]

2. 2

   Remove the PopSocket and run the plastic grip under cold water. Employ your fingernail to pry the PopSocket off of your telephone, then concord the adhesive side of the PopSocket and turn your water faucet to a low flow on cold. Run but the plastic grip of the PopSocket nether water — if you must, wrap the adhesive in a paw towel to prevent getting information technology wet and affecting its stickiness.

   • You can clean the adhesive separately, merely if y'all go it wet earlier you're ready to make clean it, you could cause the adhesive to lose some of its stickiness. Wrap it or accept care to not go information technology wet while cleaning the grip.

3. 3

   Scrub the plastic grip with the corner of a soapy rag, avoiding the adhesive. Agree the PopSocket past the sticky side again and scrub the plastic grip with the corner of a soapy rag PopSocket. Take intendance to avoid getting lather on the adhesive, and only scrub the plastic parts of the PopSocket.

   • Scrub inside the grooves of the PopSocket's expandable center section with a cotton swab soaked in soapy water.
   • Use 70 pct rubbing alcohol to particularly stubborn stains or grime with a cotton wool swab, then rinse information technology under water again. Rubbing alcohol is great for removing stains as information technology evaporates quickly and leaves no impairment.

4. 4

   Rinse the grip in one case again, then dry it with a paper towel or rag. Run the grip under water to become rid of soapy residual and rubbing alcohol, again taking intendance to avoid getting the agglutinative wet. Then, take a dry rag or a paper towel and dab the PopSocket dry until it is completely complimentary of water.^[7] Press it firmly onto the back of your phone with the sticky-side downward.

   • You can also air dry the plastic grip. Expand the PopSocket and so residue information technology on its side on a newspaper towel. This prevents the agglutinative from sticking to the towel and will however allow the grip to air dry and drip dry out.

   Advertisement

Ask a Question

200 characters left

Include your e-mail address to become a bulletin when this question is answered.

Submit

Advertising

• After re-attaching the PopSocket to your phone, wait at to the lowest degree 1 hour before you extend the grip and utilise it. This allows enough time for the agglutinative to fully stick to your phone, reducing the risk of it detaching all of a sudden.^[eight]

Thank you for submitting a tip for review!

Advert

• Avoid using rubbing booze in a airtight room, and have the PopSocket to a well-ventilated area to forestall inhaling rubbing booze fumes.

• Never allow the sticky side of the PopSocket be exposed to air for more than than 15 minutes, even when cleaning the plastic grip, as this destroys the adhesive.

Advertisement

About This Article

Cheers to all authors for creating a folio that has been read thirty,550 times.

Is this article upwards to date?

williamsfewasy.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket

Share this post